{"title":"CA Glues","description":"","products":[{"product_id":"insta-cure-™-super-glue-ca","title":"Insta-Cure+™ Super Glue, CA","description":"\u003cp\u003e\u003cspan\u003eMedium CA 2 OZ \u003c\/span\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cspan\u003eInsta-Cure+™ is a higher viscosity CA for loose fitting joints in which the adhesive must bridge gaps. Normally, the thicker CA is applied to one surface and then the parts are held tightly together for about 5 to 15 seconds. For large surface areas, including those with close fitting joints such as laminations, INSTA-CURE+ ™ should also be used. To prevent premature curing, don’t spread the glue into a thin film. Lay down a serpentine bead with about 1\" separations on one surface, then assemble the parts, letting the pressure spread the CA out.\u003c\/span\u003e\u003c\/p\u003e","brand":"BSI","offers":[{"title":"Default Title","offer_id":52935965212971,"sku":"PHBSI-108","price":11.5,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0984\/2111\/3131\/files\/DSC02279.jpg?v=1773957008"},{"product_id":"insta-cure™","title":"Insta-Cure™","description":"\u003cp\u003e\u003cspan\u003eThin CA! 2 OZ\u003c\/span\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cspan\u003eInsta-Cure™ has a water-thin viscosity that wicks deep into joints by capillary action and cures in a matter of a few seconds. Surfaces to be bonded must be tight fitting and should be held together while you apply the CA around the edges of the seam. At the moment CAs cure, they give off a vapor that can irritate the nose and eyes, so be prepared. Thin CAs work very well on balsa since they penetrate into the wood and form more than just a surface bond.\u003c\/span\u003e\u003c\/p\u003e","brand":"BSI","offers":[{"title":"Default Title","offer_id":52936649736491,"sku":"PHBSI-103","price":12.5,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0984\/2111\/3131\/files\/DSC02280.jpg?v=1773957477"},{"product_id":"maxi-cure™","title":"MAXI-CURE™","description":"\u003cp\u003e\u003cspan\u003eSuper thick CA 2 OZ \u003c\/span\u003e\u003c\/p\u003e\n\u003cp\u003eMaxi-Cure™ extra thick CA is the best CA for most plastics, including GE’s Lexan MAXI-CURE™ is the best choice for plastic model assembly. When used with INSTA-SET™, it works better than any putty for modifying or filling voids. It can be carved with a knife or razor blade and sanded and feathered to form a finish indistinguishable from plastic. MAXI-CURE™ bonds fiberglass, hardwood, metal and rubber better than any other hobby adhesive. For gluing to the inside, clothtextured surface of fiberglass, scrape the area to be bonded with a razor blade or coarse sandpaper before using MAXI-CURE™ or any other adhesive. It also is best for bonding the tires for R\/C cars.\u003c\/p\u003e\n\u003cp\u003eMAXI-CURE™ has proven to be very popular in the archery business for the fletching of vanes onto aluminum and carbon arrow shafts. Along with being the strongest, MAXI-CURE™ is usually the least expensive option for this application.\u003c\/p\u003e","brand":"BSI","offers":[{"title":"Default Title","offer_id":52936650653995,"sku":"PHBSI-113","price":12.5,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0984\/2111\/3131\/files\/DSC02281.jpg?v=1773957790"},{"product_id":"ic-2000™-rubber-toughened-ca","title":"IC-2000™ Rubber-toughened CA 1\/2 OZ","description":"\u003cp\u003eGooey stuff 1\/2 OZ Bottle\u003c\/p\u003e\n\u003cp\u003eIC-2000™ is a rubber-toughened cyanoacrylate that forms superior shock resistant bonds on non-porous surfaces. The black colored CA has added flexibility for the bonding of metals, fiberglass, rubber, carbon-fiber and other advanced materials. For model use, IC-2000™ is ideal for the bonding of bulkheads, formers and servo rails to the inside of fiberglass hulls and fuselages. Setup time is 20-40 seconds, which can be accelerated with INSTA-SET™. When cured, IC-2000™ is pliable enough to be carved with a hobby knife. IC-2000™ is the best adhesive for R\/C car tires.\u003c\/p\u003e\n\u003cp\u003eIC-2000™ has found many uses in industrial applications, such as rubber to rubber bonding by Beechcraft, carbon composite bonding by Boeing, rubber door seals by Volkswagen, speaker and subwoofer assembly in the audio industry and many others that need the most durable, shock resistant fast bonding adhesive that is available.\u003c\/p\u003e","brand":"BSI","offers":[{"title":"Default Title","offer_id":52936652914987,"sku":"PHBSI-117","price":8.25,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0984\/2111\/3131\/files\/DSC02284.jpg?v=1773958066"},{"product_id":"insta-flex-™","title":"INSTA-FLEX+™","description":"\u003cp\u003e\u003cspan\u003eGooey CA except this one is clear! 1 OZ\u003c\/span\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cspan\u003eInsta-Flex+™ clear rubber toughened has similar qualities to our black IC-2000™ but can be used in applications where you do not want the adhesive to be seen. The carbon component of IC-2000™ that gives the CA its black color also contributes to its unsurpassed strength. Since INSTA-FLEX+™ has this carbon removed, its strength is a little less than IC-2000™ but still superior to standard CA's. When esthetics are important and a flexible bond is required, INSTA-FLEX+™ is your best choice. It forms superior bonds to soft urethane and vinyl plastics. Both INSTA-FLEX™ and INSTA-FLEX+™ work well when bonding R\/C car tires. When a joint has a larger than normal gap, flexible CA's provide superior shock resistent bonds.\u003c\/span\u003e\u003c\/p\u003e","brand":"BSI","offers":[{"title":"Default Title","offer_id":52936661795115,"sku":"PHBSI-120","price":12.75,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0984\/2111\/3131\/files\/DSC02283.jpg?v=1773958700"},{"product_id":"un-cure™","title":"UN-CURE™","description":"\u003cp\u003e\u003cspan\u003eDe-bonder! For removing CA! 1 OZ\u003c\/span\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cspan\u003eUN-CURE™ debonder will soften cured CA. If parts are bonded incorrectly or your fingers are stuck together, a few drops of UN-CURE™ will dissolve the CA in about a minute. Apply on bonded skin and roll apart fingers. Once stuck, use acetone to clean off softened CA, then wash off with soap and water. Since cured CA is essentially acrylic plastic, anything that will dissolve CA will also soften most plastics. Care must be used, therefore, when using Un-Cure on plastics. Separating plastics parts with a razor saw is usually the best option.\u003c\/span\u003e\u003c\/p\u003e","brand":"BSI","offers":[{"title":"Default Title","offer_id":52936662253867,"sku":"PHBSI-161","price":8.5,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0984\/2111\/3131\/files\/DSC02282_33be4a02-37f1-4542-b8cc-a12105e57431.jpg?v=1773958989"},{"product_id":"foam-cure™","title":"FOAM-CURE™","description":"\u003cp\u003eFoam Safe CA 1 OZ\u003c\/p\u003e\n\u003cp\u003eFOAM-CURE™ is a silicone based adhesive that works very well on EPP and EPO foams. It is crystal clear and cures to a more flexible consistency than CA. It is, however, not instant bonding like CA and there is no accelerator to speed it’s curing. To obtain a faster initial bond when bonding two pieces, FOAM-CURE™ can be applied to one piece and after the two are joined, they can then be pulled apart. After letting it air dry for about ten minutes, FOAM-CURE™ will act like a contact cement when the parts are rejoined, resulting in enough tack strength to allow the next steps of assembly. Full strength is reached in 10-12 hours.\u003c\/p\u003e\n\u003cp\u003eFOAM-CURE™ works with all foams, and will actually bond most other materials. It will bond wood and plastic to foam, and is a good canopy glue. FOAM-CURE™ does not, however, cure flexible enough to act as a hinge for aircraft control surfaces. Its limitations occur when bonding large areas of two non-porous materials. FOAM-CURE™ requires exposure to air for drying. If one tried to bond, for example, a half-dollar coin to glass, over 90% of the adhesive would never cure, since the solvent it contains would have no where to evaporate. A small amount of denatured alcohol can be mixed into the Foam-Cure to make it thinner.\u003c\/p\u003e","brand":"BSI","offers":[{"title":"Default Title","offer_id":52936662876459,"sku":"PHBSI-142","price":8.25,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0984\/2111\/3131\/files\/DSC02285.jpg?v=1773959316"},{"product_id":"insta-set™-kicker","title":"INSTA-SET™ (Kicker)","description":"\u003cp\u003e\u003cspan\u003eCA (kicker) Available in small pump spray and large spray bottle!\u003c\/span\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cspan\u003eINSTA-SET™ is a catalyst which acts as an accelerator that allows CAs to quickly cure in thick layers by enhancing the alkaline conditions during polymerization. INSTA-SET™ in a spray bottle is normally used to cure the CA that flows from joints when parts are pressed together. Applying an additional bead of thick CA along a seam and then curing it with INSTA-SET™ significantly enhances a joint’s strength. For difficult to bond materials, INSTA-SET™ can be applied to one surface and CA to the opposite surface. When brought together, they will bond instantly. INSTA-SET™ is formulated with a strawberry scent and activates CA in 6 to 8 seconds without any degrading of the CAs strength, which can occur with many other accelerators. It is compatible with all surfaces, even clear plastic and white foam.\u003c\/span\u003e\u003c\/p\u003e","brand":"BSI","offers":[{"title":"2 OZ Pump Spray","offer_id":52936679358763,"sku":"PHBSI-151","price":10.0,"currency_code":"USD","in_stock":true},{"title":"6.75 OZ Aerosol Can","offer_id":52936680407339,"sku":"PHBSI-155","price":14.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0984\/2111\/3131\/files\/DSC02277.jpg?v=1773960553"},{"product_id":"super-gold™","title":"SUPER-GOLD™","description":"\u003cp\u003e\u003cspan\u003eNon Stinky Foam safe CA! 2 OZ\u003c\/span\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cspan\u003eSUPER-GOLD™ Thin and SUPER-GOLD+™ gap filling medium thickness are our odorless foam safe CAs. They are non-frosting and take only 2 or 3 seconds longer to bond compared to Insta-Cure and Insta-Cure+. There are no fumes that irritate the nose and eyes. The SUPER-GOLD™’s do not attack white foam; therefore, they can be used in the building of foam core wings and the assembly and repair of plastic and foam ARF’s. They will not fog clear plastic. SUPER-GOLD+™ is ideal for attaching clear canopies in plastic model kits; however, MAXI-CURE™ is still recommended for assembling the rest of plastic kits. Wood can be bonded to white foam with SUPER-GOLD +™ in less than fifteen seconds. For bonding foam to foam, spray a very light fog of INSTA-SET™ to one piece and apply SUPER-GOLD+™ to the other before joining. Excess INSTA-SET™ may create too much heat, which can melt the foam. Both SUPER-GOLD™’s cure to a more flexible consistency for better shock absorbtion. Whenever a large amount of CA is to be used in such applications as saturating fiberglass or Kevlar, SUPER-GOLD™ eliminates the irritating fumes from the evaporating monomer that make repeated use of CA unpleasant at times.\u003c\/span\u003e\u003c\/p\u003e","brand":"BSI","offers":[{"title":"Default Title","offer_id":52939108778283,"sku":"PHBSI-128","price":24.5,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0984\/2111\/3131\/files\/DSC02287.jpg?v=1774019658"},{"product_id":"ic-loc™-purple","title":"IC-LOC™ Purple","description":"\u003cp\u003e\u003cspan\u003ePurple is the low strength for most applications! 10 ml bottle\u003c\/span\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cspan\u003eIC-LOC™ Purple prevents loosening of small fasteners from normal use and vibration, but parts can still be disassembled with hand tools. IC-LOC™ Purple seals and prevents rusting of threads.\u003c\/span\u003e\u003c\/p\u003e","brand":"BSI","offers":[{"title":"Default Title","offer_id":52939109794091,"sku":"PHBSI-177","price":10.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0984\/2111\/3131\/files\/DSC02286.jpg?v=1774020182"},{"product_id":"ca-glue-tip-long-extender-10-pack","title":"CA Glue Tip Long Extender 10 Pack","description":"\u003cp\u003eCA bottle long flex tips! These are nice and long so they last a bit more! \u003c\/p\u003e\n\u003cp\u003e10 Pack\u003c\/p\u003e","brand":"POWERHOUSE HOBBIES","offers":[{"title":"Default Title","offer_id":52951602037035,"sku":"PHCAMT","price":2.49,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0984\/2111\/3131\/files\/DSC02263.jpg?v=1776199240"},{"product_id":"ca-glue-tip-short-extender-10-pack","title":"CA Glue Tip Variety Extender 8 Pack","description":"\u003cp\u003eCA bottle short tips! These are color coded for flow control!\u003c\/p\u003e\n\u003cp\u003e8 Pack\u003c\/p\u003e\n\u003cp\u003eThese have different outlet sizes at the tip for use with different viscosity CA glues!\u003c\/p\u003e","brand":"POWERHOUSE HOBBIES","offers":[{"title":"Default Title","offer_id":52951606329643,"sku":"PHSCT","price":2.49,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0984\/2111\/3131\/files\/DSC02262.jpg?v=1776199272"},{"product_id":"ca-glue-tip-variety-extender-10-pack","title":"Ca Glue Tip Variety Extender 10 Pack","description":"\u003cp\u003eCA tips! 10 Pack!\u003c\/p\u003e","brand":"POWERHOUSE HOBBIES","offers":[{"title":"Default Title","offer_id":52951699325227,"sku":"PHGTE","price":2.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0984\/2111\/3131\/files\/DSC02261.jpg?v=1776199308"},{"product_id":"zap-a-gap-medium-ca","title":"ZAP-A-GAP MEDIUM CA","description":"\u003cp\u003eZAP-A-GAP MEDIUM CA \u003c\/p\u003e\n\u003cp\u003e \u003c\/p\u003e","brand":"ZAP","offers":[{"title":"2 OZ","offer_id":53173958869291,"sku":"PHZPT01","price":16.39,"currency_code":"USD","in_stock":false},{"title":"1 OZ","offer_id":53173958902059,"sku":"PHZPT02","price":9.59,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0984\/2111\/3131\/files\/ZAP_PT02_CA_Medium_Glue_1_oz._28.3g__22467.jpg?v=1776108574"},{"product_id":"zap-a-gap-thin-ca","title":"ZAP-A-GAP THIN CA","description":"\u003cp\u003eZAP-A-GAP THIN CA \u003c\/p\u003e","brand":"ZAP","offers":[{"title":"2 OZ","offer_id":53173991375147,"sku":"PHZPT07","price":16.39,"currency_code":"USD","in_stock":false},{"title":"1 OZ","offer_id":53173991407915,"sku":"PHZPT08","price":9.59,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0984\/2111\/3131\/files\/R.png?v=1776108820"},{"product_id":"slo-zap-thick-ca","title":"SLO ZAP Thick CA","description":"\u003cp\u003eSLO ZAP Thick CA\u003c\/p\u003e","brand":"ZAP","offers":[{"title":"1 OZ","offer_id":53237121417515,"sku":"PHZPT20","price":9.89,"currency_code":"USD","in_stock":false},{"title":"2 OZ","offer_id":53237121450283,"sku":"PHZPT33","price":16.99,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0984\/2111\/3131\/files\/ZAP-PT20.webp?v=1776109160"}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0984\/2111\/3131\/collections\/images_4af6adc1-9943-4281-88de-c760d2c3e2db.jpg?v=1776112895","url":"https:\/\/powerhousehobbies.com\/collections\/ca-glues.oembed","provider":"POWERHOUSE HOBBIES","version":"1.0","type":"link"}